This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
electrical:12v:charging [2019/07/17 08:17] frater_secessus [charging deep cycle batteries] |
electrical:12v:charging [2020/07/08 11:29] frater_secessus [float stage] |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | [[lifestyle: | + | [[lifestyle: |
+ | |||
+ | > “Three stage chargers are easier on your batteries, charge them faster, fuller and help you use less water”((https:// | ||
+ | |||
+ | |||
+ | > A [ [[electrical: | ||
+ | |||
+ | > Charging lead acid batteries is not something that you decide to do, or start or stop. The old statement, "I need to idle the engine for a few minutes to "top off" the batteries." | ||
====== charging deep cycle batteries ====== | ====== charging deep cycle batteries ====== | ||
Line 31: | Line 39: | ||
==== absorption stage ==== | ==== absorption stage ==== | ||
- | The absorption stage, sometimes called // | + | The absorption stage, sometimes called // |
+ | |||
+ | Absorption **begins when the battery reaches the absorption voltage** ([[electrical: | ||
+ | |||
+ | Example: | ||
+ | |||
+ | |||
+ | In practice absorption takes longer when the battery has been discharged deeply and shorter when it has not.((http:// | ||
+ | |||
+ | **Mythbuster: | ||
+ | |||
+ | > charge current affects the SOC transition point from bulk to absorption charging - MaineSail((https:// | ||
+ | |||
+ | MaineSail found that | ||
+ | |||
+ | * charging AGM at C/2.5 (max rate) resulted in the battery being 63.3% " | ||
+ | * charging AGM at C/5 (min rate) resulted in the battery being 77.4% " | ||
- | Absorption **begins when the battery reaches the absorption voltage** ([[electrical: | ||
Some controllers will allow the user to configure the time or ratio of capacity/ | Some controllers will allow the user to configure the time or ratio of capacity/ | ||
- | > If your charge controller only holds [absorption] voltage for an hour or two, that is likely not enough time. As long as [there is a load] and you cycle the battery daily, you could set float voltage to 14.8v [to match absorption] without worry. Only when you stop cycling the battery do you need to return float voltage to more regular 13.2v levels. Premature application of float voltage by automatic charging sources is a battery killer.((http:// | + | > If your charge controller only holds [absorption] voltage for an hour or two, that is likely not enough time. As long as [there is a load] and you cycle the battery daily, you could set float voltage to 14.8v((for example - secessus)) |
+ | |||
+ | If Absorption cannot be completed in the max amount of time configurable in the controller (due to damaged/old batteries), **charging at the minimum rate and/or at higher voltage may help [[electrical: | ||
+ | |||
+ | |||
+ | |||
==== float stage ==== | ==== float stage ==== | ||
Line 43: | Line 73: | ||
Common Vfloat values range between 13.2v for stored batteries to 13.8v for banks that are deep cycled each day. | Common Vfloat values range between 13.2v for stored batteries to 13.8v for banks that are deep cycled each day. | ||
+ | |||
+ | also see [[electrical: | ||
Line 84: | Line 116: | ||
===== charging other chemistries ===== | ===== charging other chemistries ===== | ||
- | See [[electrical: | + | See [[electrical: |
===== equalization ===== | ===== equalization ===== | ||
Line 110: | Line 142: | ||
- ambient temperature as measured by the charger. | - ambient temperature as measured by the charger. | ||
- in the absence of actual measurements the charger will likely use the 77F laboratory standard. | - in the absence of actual measurements the charger will likely use the 77F laboratory standard. | ||
+ | |||
+ | This automatic voltage tweaking for temperature may result in your actual battery voltages being observably higher in cold temps and lower in hot temps. | ||
===== watering batteries ====== | ===== watering batteries ====== | ||
Line 140: | Line 174: | ||
**Manual chargers** will not be affected by load as they are controlled by the user. | **Manual chargers** will not be affected by load as they are controlled by the user. | ||
+ | |||
+ | |||
+ | ===== battery voltage while charging ===== | ||
+ | |||
+ | Battery Voltage = Battery Voc((resting voltage)) + (Charge Current x Ri((internal resistance))) | ||