====== Alternator details ====== Also see the [[electrical:12v:alternator|alternator charging overview]] article. ===== theory of operation ===== An oversimplified overview will help us understand the challenges and approaches to overcoming them. - An alternator makes alternating current ("AC", hence //alternator//) by rotating an electromagnetic - field through stationary wires ("windings") - the AC is turned into direct current ("DC") when passing through "rectifying" diodes - **voltage output** is controlled by current production - **current production** is controlled by varying the field current energizing the electromagnetic field All vehicles monitor("sense") output voltage and adjust alternator output to maintain that voltage. Modern vehicles often monitor alternator heat and limit current to prevent damage. Older vehicles may not. Setups with external requlators (see below) can carefully control alternator output to achieve specific results. Many of the lessons learned about bank charging by alternator have been learned from [[https://www.cruisersforum.com/forums/|people who live on boats]]. Most of their power is generated from the alternators while they "cruise" at slow speeds throughout the day. Their use case is extreme: > On boats alternators are low RPM, in an enclosed space with bad airflow, charging huge batteries and large loads((https://www.cruisersforum.com/forums/f14/balmar-alternator-temperate-protection-settings-241443-4.html#post3723245)) ===== the challenges ===== Our banks will see two things when charged from alternator: voltage and current. Bot need to be appropriate for the chassis and the house bank. Producing power makes heat as a by-product. Excess heat can destroy the alternator. How do we balance the bank's thirst for current while protecting the alternator from itself? ==== voltage ==== Alternator voltage output is intimately related to current. In the simplest model the alternator's voltage is controlled((//regulated//)) by a voltage regulator. The regulator uses current to hit the desired voltage setpoint. - vehicle voltage stable at 14.0v (for example) - loads are added, causing system voltage to drop to 13.7v - regulator tells alternator to make more current, causing voltage to stabilize at 14.0v - loads are removed, causing system voltage to rise to 14.2v - regulator tells alternator to make less current, causing voltage to stabilize at 14.0v >> [the alternator] has no way of knowing how great the load is. It only cares about the voltage at the regulator terminals. if it is below the set point, it will produce all of the power it possibly can at the given RPM's. If it is at the set point, it will reduce the power generated to the level that will not overshoot the set point voltage. The battery is what is supplying the power to the load and the alternator is trying to keep it at the set point voltage. -- [[https://diysolarforum.com/threads/controlling-charge-from-multiple-sources-to-keep-lifepo4-batteries-from-continual-100-charge.53461/post-701101|hwse]] Note: **Smart((multi-voltage)) alternators** do not have a firm voltage setpoint; they vary the voltage target based on conditions. This is intended to improve overall MPG. Voltage might plummet during full acceleration (to free up engine power) then spike quite high in other conditions. This wide variance complicates bank charging, and typically means [[electrical:12v:b2b|a DC-DC charger]] is required. === regulation === Most alternators have been //internally-regulated// -- the voltage regulator is built into the alternator case itself. **Externally-regulated alternators** are alternators where the regulation function is physically separated from the alternator. There may be a stand-alone external regulator or the engine ECU may assume those duties. see [[electrical:12v:alternator_details#external_regulation|External Regulation]] below === tricking the regulator === Since the alternator only knows what voltage it is receiving at the regulator, an alternator can be tricked into adjusting output voltage by: * sensing voltage at somewhere other than the starter battery((the usual place)) * placing something inline with the sense wire that changes the voltage. This might be done to increase charging voltage in order to increase current, or might be to compensate for voltage drop through [[electrical:12v:alternator#proper_isolators|a diode-based isolator]]. Be careful to keep alternator output voltage in a range acceptable to the vehicle itself. ==== current ==== The specs for your alternator will include an amp (A) rating. This might be 80A for a passenger car, 150A for a cargo van, or >200A for a heavy duty vehicle. You can often find the actual rated output of your alternator in your manual, vehicle specs, or using a VIN lookup tool for your brand of car. This rating is a measure of how much electrical current it can make under optimal conditions, typically: * while the alternator is cold;((exceptions: Balmar hot rates at 190F, Ample at 200F and Electromaax at 220F. https://forums.sailboatowners.com/threads/balmar-alternator.157507/post-1071017)) and * being spun at an appropriate RPM These conditions are not often present in normal use. For this reason a **continuous duty rating** (CDR hereafter) is more helpful for assessing how hard we can push the alternator. In the absence of a stated CDR we can assume CDR is roughly **50% of the alternator's output rating**.((https://www.irv2.com/forums/f54/dcdc-size-calculations-601423.html#post6384928)) The continuous duty rating is the limiting factor when charging house batteries or running other long-duration loads. Note that **the CDR does not represent how much power is available for house battery charging**; the vehicle still has to run its own loads like ECU, lights, fans, etc. For the purposes of this discussion we will assume a cargo van with an alternator rated **140A**. === how many amps can I pull from the alternator? === {{ https://img.mousetrap.net/misc/transit250alternator.jpg?150}} Alternator output in the short term and longer term is affected by several factors * the **rating** above * **alternator RPM**, which is proportionally related to engine RPM.((the alt pully to crank pulley ratio is typically around 3:1; the alt spins 3x as fast as the crankshaft)) The rated output above cannot be reached at idle((and shouldn't be, due to reduced ventilation because the vehicle is standing still)) * **heat**, which is the destroyer of alternators In the absence of further information one might use some crude rules of thumb: * **at idle** discretionary loads **≤25% of rated output**.((50% of CDR)). For our 140A alternator this would be 35A. Note: this is about stopping at red lights or in traffic; [[rv:idling|idling the engine to charge batteries is not recommended]]. * **while driving** loads ≤33% (66% of CDR) For our 140A alternator this would be 47A. * if **alternator output voltage drops below normal**, the belt starts to squeal or engine RPM is affected the alternator is overloaded and loads should be reduced or [[electrical:12v:alternator#disabling_alternator_charging|charging disabled]]. One could make **a more informed decision** this way - acquire the output chart for your alternator - use a clamp meter to see what current the chassis draws with blower on, lights on, etc at a given engine rpm - do the math: [output rating at that rpm / 2] to get continuous output rating at that rpm. Subtract chassis loads. The remainder is what you have left over to use. The **optimal arrangement** is a temp-sensing [[electrical:12v:alternator_details#regulation|external regulator]] that runs the alternator at **maximum safe output** when required and lower output when temps get too high. A poor man's version of the temp-sensing regulator involves [[electrical:12v:alternator_details#thermal_switches|epoxying a thermistor to the alternator housing]]. This turns off the charger/relay at a given temperature. In some scenarios output might be limited by [[https://diysolarforum.com/threads/many-here-say-that-an-alternator-should-not-be-connected-to-lifepo4-and-that-one-should-use-dc-dc-charger.53318/post-705080|placing a resistor in series with the alternator's field control wire]]. If one is completely stumped: - default to the smallest [[electrical:12v:b2b|DC-DC]] available, typically 15A-20A - avoid idling the van to charge == effect of alternator charging method on current == The various charging methods have different costs, some have different install locations((DC-DC should be mounted as close to the battery bank as practical)), levels of voltage/current control, etc. Example: since charging voltage is a fundamental part of the current formula I=V/R we can have different charging currents, all other things being equal. Let's assume a battery bank at 12.1v, alternator at 14.2, total circuit resistance of 40mR, and a DC-DC configured to charge at 14.4v: * relay - (14.2-12.10) / 40mR = **53A** * diode-based isolator - (13.5-12.10) / 40mR = **35A** * DC-DC - (14.4v - 12.10) / 40mR = **58A** ==== heat ==== Heat in the alternator comes from * the engine block (radiation) * ambient temperatures * the alternator itself - alternators are most efficient (produced the least heat per watt) at normal vehicle cruising speeds. At low RPM and high RPM more heat will be generated: * rectifying diodes((change alternator AV to chassis DC)), which increases as current demand increases - some setups place the rectifying diodes outside the case to reduce this heat((https://diysolarforum.com/threads/many-here-say-that-an-alternator-should-not-be-connected-to-lifepo4-and-that-one-should-use-dc-dc-charger.53318/post-810052)) * bearing heat (increased friction from failure, misalignment, overly-tight belt, etc) * the coils Cooling comes from: * alternator fans, typically two attached to the rotor inside the case, but some have external fans. These fans do not move sufficient air at idle RPM. * ambient airflow (breezes, forward motion, external fans). When the vehicle is not moving airflow under the hood is greatly decreased. * case surface area, so large-case alts tend to run cooler((https://www.sailmagazine.com/.amp/diy/too-hot-to-handle)) * current reductions, if temperature-sensing regulation is present * moving hot items outside the case (see rectifying diodes above) > If you want the alternator to run cool rip out the internal rectifier and build an external rectifier... Otherwise fit large frame alt and run it at a current limited output. Maine Sail((https://forums.sailboatowners.com/threads/wouldnt-it-be-cool.1249934025/post-1750512)) === heat-related failure modes === Alternator heat is typically measured on the case, although internal parts will be hotter. > Temp sensor should be measuring as close to the stator as possible((https://forums.sailboatowners.com/threads/alternator-temperatures.1249934414/post-1780143)) A common rule of thumb for a safe upper limit on case temps is 100C/212F((https://www.cruisersforum.com/forums/f14/balmar-alternator-temperate-protection-settings-241443.html)), although more conservative temperatures might be advisable. {{ https://img.mousetrap.net/misc/SAEAltTemps.jpg?100}}Critical internals will be hotter than the case itself. For example, during [[electrical:12v:drop-in_lifepo4#but_that_Victron_video|the infamous Victron video]] both internal and external temps were given for the Balmar setup making 50A @ 2,100rpm. The case was 42C (108F) while the internals were 74C (165F). This alt was on a bench rather than mounted to a hot engine block. See table at right for examples of external/internal temps observed during lab testing.((https://www.cruisersforum.com/forums/f14/alternator-temp-what-is-normal-range-228245-2.html#post3114736)) * rectifier diodes are typically designed for a max of 150C (300F)((https://forums.sailboatowners.com/threads/alternator-temperature.1249925187/post-1644189)). More modern alternators may have diodes that can survive higher temperatures.((https://www.cruisersforum.com/forums/f14/alternator-temp-what-is-normal-range-228245.html#post3044758)) * the varnish insulation on the windings will be degrading by 155C (310F) * if temperature compensation is present it may begin around 255-260F.((https://www.stevemeadedesigns.com/board/topic/103934-alternator-operating-temperatures/?do=findComment&comment=1442616)) The quote above about using 120C may be a designed to cut alternator charging just before the ECU/regulator kicks in. === thermal switches === In [[https://www.youtube.com/watch?v=bjeHJd6OO2Y&lc=Ugyusa6wH9p3jNMKbmh4AaABAg.9m5OeSgBRtB9m5UO1ANIfF|a comment]] on [[https://www.youtube.com/watch?v=bjeHJd6OO2Y|an excellent video about charging lithium from the alternator]] WorkingOnExploring talks about adding overtemp protection with a thermal switch (a small bimetallic switch):((see [[https://www.youtube.com/watch?v=kF4Yxo9C9DM|this teardown and demo video]] on youtube)) >> [[https://amzn.to/3luTwwx|a KSD9700 120C]], normally closed thermal switch epoxied to your alternator case. That way, if some abnormal event occurred and the alternator overheated, it could deactivate the [combiner] till the alternator cooled. It would likely cost less than $20 to install this thermal safety. The idea here is to run the relay's control circuit((manual or D+ wire, //not// the charging wire)) through the **N**ormally-**C**losed((ie,circuit completed)) thermal switch. When the switch hits the defined temperature the circuit opens((breaks)) and power to the combiner is cut off; house bank charging from the alternator is stopped. The switch will typically reset when temperature drops by ~25%; read the datasheet for your switch for specific details. If one had a DC with a current-limiting function ([[electrical:12v:b2b#renogy1|renogy's 20-40-60A models]], for example) or DC-DC in parallel one could use two different-spec switches to achieve staged charging. Using placeholder temps: - run an aggressive charging setup full blast - at 90C engage current limiting - at 120C disable charging completely Note: 120C = 248F. Other temps like 90C (194F) and 100C (212C) are available and may be gentler on the alternator. Because the alternator is mounted to the block the alternator case may be at the ~same temp as the block. Check case temps when engine has been running to get a feel for how hot the case should be, preferably at the location the diodes are heat-sinked to the alternator case.((https://forums.sailboatowners.com/threads/alternator-temperature.1249925187/post-1644191)) === manual switches === It is often possible to [[electrical:12v:alternator#disabling_alternator_charging|disable alternator charging]] when ambient heat, traffic jams, or other factors conspire to overheat the alternator. === known temperature configurations === * Balmar alternators are rated for continuous duty at 85C.((https://www.cruisersforum.com/forums/f14/what-is-my-alternator-doing-276970.html#post3792740)) * The Balmar Series 6 normal temp is 82C with max of 108C.((https://www.trawlerforum.com/forums/showpost.php?p=853938&postcount=6)) * The Balmar ARS-5 with MC-TS-A temp sensor by default starts derating alternator output at 109C.((https://www.cruisersforum.com/forums/f14/alternator-temperature-169339.html#post2164575)) * The Balmar MC-612 with temp sensor starts derating at 107C.((https://balmar.net/wp-content/uploads/2016/02/MC-612-Regulator-Manual-2005-2009.pdf)) It can derate ~55%.((https://www.irv2.com/forums/f87/alternator-burn-out-from-lithium-batteries-558284-8.html#post6426941)) * DC Power Solutions alternators are ok to 107C.((https://www.cruisersforum.com/forums/f14/alternator-temperature-169339.html#post2164617)) === idling to charge house batteries === Idling the engine to charge house batteries is a perfect storm of **underperformance** * the alternator is spinning too slowly to make the CDR and heat * the alternator is spinning too slowly for internal cooling fans to work well * the alternator is producing more heat than power due to inefficiency * there is no airflow from forward movement to directly cool the alternator... * ... or to remove superheated air under the hood The situation is bad enough with relays, but even worse worse with DC-DC because * they tend to hold full output for hours on end rather than tapering * when the alternator struggles and voltage drops the DC-DC will demand //more// current to make its output target. Hopefully the charger has a minimum chassis voltage for operation and will not drag the chassis down excessively === anecdote === >> We have 500ah of lithium that can be charged at 3C, a theoretical 1,500 ampere charge rate. We have the Nations 280 amp second alternator. We control the Nations alternator with a DIY regulator that allows us to pretty much set the charge level anywhere we please. We'd be pleased to set it to 200+ amps, but that turns out to be impractical. The reality is, **if we set the charge rate to 125 amperes, we cannot continuously charge at this rate while standing still unless the outside air temperature is 55 degrees or below**. **When driving at highway speeds (which cools the alternator), we can run a continuous 150 ampere charge rate** at virtually any outside air temperature. While we have not tested this further, we suspect that should we desire to 'up the ante' much beyond our current 150 (sometimes 175) amperes, we would again find ourselves temperature limited even while driving. - [[https://www.promasterforum.com/threads/idea-help-wanted-alternator-charging-house-batteries-only.96415/post-766319|winston]] ===== common modifications ===== ==== external regulation ==== External regulation can provide overtemperature protection (see section on Heat above), current limiting, and can also cause the alternator to behave like a smart charger with [[electrical:12v:charging|multistage charging]]. In a camper/RV context //an externally-regulated alternator// typically means an **aftermarket external regulator** controlling a **dedicated secondary alternator**.((on boats there is typically one externally-regulated alternator that runs the electrics and charges the house bank. Modern land vehicles are likely less tolerant of the alternator doing things the ECU did not command.)) Depending on the implementation external regulation might provide: * configurable current levels and/or voltage setpoints * [[electrical:12v:charging|multistage (smart) charging]] * temperature monitoring so maximal current can be extracted without overheating * RPM-based output limits * slowly ramping up current to avoid belt slippage/damage * shutoff when commanded by BMS * CANBUS and other communication * etc External regulators include: * Balmar ARS-5 (no external voltage sensing) * Balmar MC-614 (external voltage sensing) * Xantrex Xar (no external voltage sensing) * Wakespeed WS500 (CANBUS) * [[https://theyachtrigger.com/arco-zeus-alternator-regulator/|Arco Zeus]] - new to market * [[https://www.mastervolt.com/products/alpha-pro-mb-charge-regulator1/alpha-pro-iii/|Mastervolt]], more often seen in marine installs * [[https://sterling-power.com/collections/alternator-regulators|Sterling]] === P-type vs N-type regulation === The alternator is controlled by varying the signal on the field control wire. The strength of the electromagnetic field drives current, which drives system voltage. The field control wire can be on the **P**ositive((Grounded Field type, https://workingonexploring.files.wordpress.com/2023/02/understanding-the-alternator.pdf)) or **N**egative((Grounded Regulator type)) side of the field control circuit. Most internally-regulated OEM alternators are P-type with the regulation occurring on the positive side. [[https://balmar.net/faq/|Balmar only builds P-type regulators]] because: >> With an N-Type design, if the field wire shorts to ground, or if the alternator internally shorts to ground, the alternator will immediately produce full output... with... P-Type regulation... if the field wire shorts to ground or the alternator develops an internal short, the included fuse on the field wire simply blows and the alternator stops all output... When converting these units to be used with a Balmar external regulator, the alternator must also converted to P-Type for safety and compatibility with our regulators Wakespeed apparently regulates on the P side but [[https://www.wakespeed.com/learn/|offers a N-type harness]]: >> The vast majority of the time, a P-type harness will work — although there are some regions like Europe, where externally regulated N-type alternators are more commonplace. In most situations where an alternator is being modified to support external regulation, the technician making the modification has the option to set up the alternator for P-type regulation. This is by far the most commonly chosen field excitation route. Just about all of the aftermarket externally regulated alternators available in the U.S. will be configured to be excited on the positive brush. If you are not familiar with the modification process, we do recommend having a competent alternator technician modify your alternator for you. ==== Heavy duty / high output ==== Alternators can be built in heavy duty configuration, which typically connotes: * higher current rating * increased internal cooling (ie, more or better fans) * ability to make more power in idling scenarios, which is useful for police vehicles, ambulances, and other vehicles that need to idle for long periods of time. HD alternators for any particular vehicle may be bolt-ins with no modifications required. They do cost somewhat more. The labor cost would remain the same so some people choose to upgrade the alternator when/if the OEM one fails. [[https://www.nationsstarteralternator.com/|Nations]] and similar alternator builders make alternators for specialty uses. Note that increasing alternator output may require upgrading stock chassis wiring: >> To run a [high output] alternator, ALL of your engine's factory high current cabling will need to be [sized] to support it, including engine and starting battery grounds, and alternator positive. -- MechEngrSGH((https://www.irv2.com/forums/f87/alternator-burn-out-from-lithium-batteries-558284-8.html#post6428559)) ==== Idle optimized ==== Some tricks are possible to get higher outputs at lower alternator RPM. Denso uses square windings in some units to pack the windings more tightly.((citation needed)) Smaller alternator pulleys may be used to increase alternator RPM at low engine RPM. Caveat: this can overspeed the alternator on higher-rpm engines. ==== large case ==== Alternator cases come in two general sizes: large and small. Most vehicles come stock with small case alternators because they are easier to "package" (fit into the available space). Semis, boats, and other vehicles with fewer space limitations may use large case alternators, allowing for more internal cooling, larger or more separated components, ease of repair, higher constant duty outputs, etc. One is not //better// than the other; they are meant for different applications. The mounting bolt pattern may be the same or it may require a different mount. Pulleys, belts, and/or belt lengths may need to be changed. ==== dual alternators ==== === aftermarket dual setups === In some setups a second alternator is fitted, often externally regulated (see above) and dedicated to charging the house bank. This allows different voltages (24v or 48v) for charging specialty house banks. If the house bank is Lithium one must plan for sudden BMS disconnect and the effect this would have on an alternator. In a single-alternator scenario the starter battery would provide buffering against load dump. Balmar 2nd alt kits for Sprinter, Transit, and Promaster can be seen [[https://balmar.net/wp-content/uploads/2022/09/PDS-XT-MS-170-K6-KIT.pdf|in this brochure]] (pdf). === OEM dual setups === OEM (factory) dual alternator setups may not behave as one expects. Typically they are controlled separately but both tied to chassis voltage. == Ford == On recent models the dual alts are set up so the primary maxxes out before the secondary kicks in: > In dual generator systems, the PCM keeps the secondary generator in a standby state where it does not generate current unless the primary generator is generating full power and more current is needed to support the vehicle loads. The PCM monitors the output of the primary generator and adjusts the control setpoint of the secondary generator to cause it to provide additional current when needed.((https://www.ford-trucks.com/forums/1610126-dual-extra-heavy-duty-alternator-2.html#post19653623)) [[https://youtu.be/uwrG3gUdDT8?t=725|This behavior surprised Mortons on the Move]], thwarting their alternator-charging plans. Known configurations: * 397A = 220A + 157A * 332A = 175A + 157A There may be Stationary Elevated Idle Control (SEIC) ("high idle") available. == RAM == * 380A = 220A + 160A > There is a process to electronically remove the second alternator from the computer by deleting the sales code and that essentially has the truck setup as if it came with just a single one from the factory.((https://forum.expeditionportal.com/threads/second-alternator-charging-lithium-battery-bank.224394/post-2921675)) == GM == Information is limited, but GM factory dual alt setups appear to run the way one would expect in the first place, with load shared between them: > The two alternators are controlled over a common circuit from the ECM so they cannot be controlled independently. The ECM cannot shut one down and let the other one run. It is both or neither.((https://www.duramaxforum.com/threads/dual-alternator.934098/post-11906770)) [[https://www.duramaxforum.com/threads/dual-alternator.934098/post-11906642|This upfitters guide excerpt]] contains additional information. ==== DUVAC ==== Some older Class A and C RVs came with DUVAC (DUal Voltage Alternator Control)((https://www.countrycoachforums.com/index.php?PHPSESSID=3ggkjl41c5lrkrerduih87oeif&topic=6840.msg34665#msg34665)) setups, which use separate voltage-sensing wires for the house bank. > This Duvac system that Leese Neville came up with was a completely integrated dual battery/isolator setup that was “state-of-the-art” in ’99((diode-based isolators)) but soon was obsoleted by newer better technology.((voltage-sensing relays and DC_DC chargers))((https://www.foreforums.com/index.php?PHPSESSID=bs0n0psbr6rrvd240rv4ijvg1p&topic=33250.msg432529#msg432529)) > ...the primary reason for DUVAC is to allow the alternator to "compensate" for the voltage loss (turned into heat) in the old generation **diode-based battery isolators**. There is approximately a .7 VDC loss through the battery isolator. The sense wire/terminal allows voltage on the battery side of the isolator to control the alternator voltage.((https://www.irv2.com/forums/f115/eliminating-the-duvac-system-539048.html#post5772417)) {As far as I can tell this was a workaround from when many isolators were diode-based so the alternator could not "see" aux battery voltage on the combined circuit((https://www.foreforums.com/index.php?PHPSESSID=bs0n0psbr6rrvd240rv4ijvg1p&topic=33250.msg300875#msg300875)) -- secessus} See [[https://www.dixie-electric.com/tsb/TSB_704.pdf|this TSB]]. (PDF) ===== sudden load disconnect ===== The alternator's voltage regulator responds to demand, increasing and descreasing field strength (and therefore output) as required to hold a given voltage setpoint. * when **large loads are suddenly added** chassis voltage will drop briefly while the regulator responds. * when **large loads are suddenly removed** chassis voltage will spike briefly while the regulator responds. If the chassis cannot absorb this spike the excess power can be dissipated within the alternator itself and cause damage **In theory** if the BMS disconnects charging the resulting spike could damage the alternator. Team Karst explains it colloquially: >> Alternator is chugging along, delivering 50 Amps. Suddenly, the output is disconnected. Since the regulator has a time constant, plus the field current can’t collapse instantly, plus stator windings, being coils, therefore inductive, they hold energy, there becomes a high positive voltage at the B+ port to keep the current flowing for a time. This transient energy may manifest itself in switch arcs, and other undesirable voltage excursions.((https://www.cruisersforum.com/forums/f166/myth-of-alternator-damage-cause-by-bms-disconnect-258292-6.html#post3532355)) This is called a //load dump//; the load is dumped (demand reduced to 0A) and there is nowhere for power in the alternator to go. As we will see, in normal installs there //are// places for the power in the alternator to go. **In practice**: * [a wise user will not be bouncing off the BMS in the first place -- Secessus] * the vast majority of lithium banks charged by alternator do so in combination with the starter battery. The lead battery will help absorb spikes from the alternator. "Batteries have about 1000F ( farad ) [capacitance] per 150Ah of capacity so they act as very substantial capacitors. Hence they have enormous ability to absorb spike energy."((https://www.cruisersforum.com/forums/f166/myth-of-alternator-damage-cause-by-bms-disconnect-258292-7.html#post3533042)),((https://www.cruisersforum.com/forums/f166/myth-of-alternator-damage-cause-by-bms-disconnect-258292-8.html#post3533143)) * modern alternators have avalanche diodes and fast-acting regulators that can adjust within 100ms.((https://www.cruisersforum.com/forums/f166/myth-of-alternator-damage-cause-by-bms-disconnect-258292.html#post3527179)) * if BMS disconnect caused alternator damage [[electrical:12v:alternator#lithium-specific_vsr|the Li-Bim]] recommended by Battle Born would quickly eat alts. It disconnects the bank from alternator every 35 minutes.((15min on, 20mins off)) The question for the user is: how much charging current are we talking about, and does the alternator already handle that level of sudden disconnect under normal operation? Secessus provides this example: > my van's radiator cooling fans are rated at 65A((https://www.promasterforum.com/threads/180-amp-alternator-with-amp-clamp-on-output.99118/post-792681)) and turn on/off frequently. My Li charging current is less than that. In addition, the speed of the disconnect plays a part: > there is a massive difference in the voltage spike from a 5 uS relay disconnect and a 10mS mosfet disconnect((https://www.cruisersforum.com/forums/f166/myth-of-alternator-damage-cause-by-bms-disconnect-258292-7.html#post3532864)) ==== exception: dedicated secondary alternators ==== Secondary alternators dedicated to Li charging will not have a starter battery or other loads inline to absorb spikes. In this case the owner might: * use a CANBUS or similar setup where the BMS can notify the alternator regulator of imminent shutdown ahead of time to allow orderly reduction of power; or * use a protection device, like [[https://www.sterling-power-usa.com /SterlingPower12voltalternatorprotectiondevice.aspx|the Sterling Alternator Protection Device]]; ([[https://www.sterling-power-usa.com/library/Sterling%20Power%20Alternator%20Protection%20Device.pdf|manual]]), [[https://balmar.net/product/apm-12/|Balmar APM]], etc. * some maintain a small lead battery in parallel with the Li bank Note that the Sterling device uses "a small resistive load" (milliAmps) to control the spike. ===== further reading ===== * Nigel's [[https://www.sailmagazine.com/.amp/diy/too-hot-to-handle|Too Hot to Handle]] article * [[https://www.electronics-cooling.com/2002/05/thermal-design-challenges-in-automotive-alternator-power-electronics/|Thermal Design Challenges in Automotive Alternator Power Electronics]] * [[https://www.youtube.com/watch?v=Kw17G76JnWQ|Small case vs Large case alternators. Know your application!]] (youtube) * WorkingOnExploring series on alternator charging * [[https://www.youtube.com/watch?v=gDIsOaEI9Wo|Part 1]] * [[https://www.youtube.com/watch?v=bjeHJd6OO2Y|Part 2]] * [[https://www.youtube.com/watch?v=lYGHAI25wvI|Part 3]] * transient voltages * [[https://www.allaboutcircuits.com/technical-articles/transient-voltage-suppressors-tvs-an-introduction/|An Introduction to Transient Voltage Suppressors (TVS)]] * [[https://www.electronicdesign.com/technologies/power/article/21801510/eliminate-those-automotive-loaddump-circuitprotection-headaches|Automotive Load-Dump Circuit-Protection Headaches]]