User Tools

Site Tools


electrical:12v:battery_monitor

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
electrical:12v:battery_monitor [2020/04/15 23:47]
frater_secessus [how they work]
electrical:12v:battery_monitor [2024/03/06 17:44] (current)
frater_secessus [inexpensive shunts]
Line 1: Line 1:
 ====== Battery monitors ====== ====== Battery monitors ======
  
-We want battery monitors be "gas gauges" but they are not. The monitor is more like the Range information on the dash that uses historical and present information to make an educated guess about how far you might get.+ 
 + 
 +===== TL;DR ===== 
 + 
 +[[https://amzn.to/4bxDjw8|{{ https://m.media-amazon.com/images/I/71g0M+mQjIL._AC_UL320_.jpg?100}}]] 
 +  * Battery monitors start from a known State of Charge then count every Amp going into or out of the battery bank 
 +  * these measurements can go astray ("drift") over time and require recalibration 
 +  * drift will be more noticeable with lead chemistries than lithium 
 + 
 + 
 +===== overview ===== 
 + 
 +We might want battery monitors be exact "gas gauges" but they are not. They do their best to keep track of incoming and outgoing current to estimate present [[electrical:depth_of_discharge|State of Charge]].
  
  
Line 10: Line 22:
   * a calculation on capacity used/remaining   * a calculation on capacity used/remaining
  
 +Typically the shunt is placed between the battery bank's negative post and the system's "ground".((negative/return side of the circuit))  The display is mounted remotely where it is convenient to view. 
 +
 +Heads up:  there are //uni//directional monitors sold for purposes other than battery monitoring; read the specs and reviews to make sure what you are getting. 
 +
 +===== sizing =====
 +
 +The shunt should be sized to handle your highest expected demand comfortably. For example, a system designed for 80A of current would require a 100A shunt.  A 25A shunt would be damaged while a 1000A shunt would not measure smaller currents accurately.
 ===== how they work ===== ===== how they work =====
  
Line 15: Line 34:
  
   - you tell the monitor the battery's [[electrical:12v:battery_capacity|capacity]], usually in Ah and printed right on the battery.  Remember that lead batteries are typically only used to about 50% of their rated capacity.  You'll either be making that mental adjustment when you configure the meter or when you read it later.  Battery capacity will also degrade over time, requiring the capacity setting to be adjusted periodically.((every 6 months? 12 months?))   - you tell the monitor the battery's [[electrical:12v:battery_capacity|capacity]], usually in Ah and printed right on the battery.  Remember that lead batteries are typically only used to about 50% of their rated capacity.  You'll either be making that mental adjustment when you configure the meter or when you read it later.  Battery capacity will also degrade over time, requiring the capacity setting to be adjusted periodically.((every 6 months? 12 months?))
-  - you tell the monitor the voltage at which the battery is presumed to be at [[electrical:depth_of_discharge|100% State of Charge]].  For lead this will be something like 12.7v; check your [[electrical:solar:charge_controller_setpoints|battery manufacturer's technical info]] for this value. +  - the monitor needs to know where it is starting from.  This is either 0% (empty) or 100% (fully charged).  You might [[electrical:12v:battery_monitor#drift_and_reset|manually reset]] the monitor at those points, or it might automatically reset to 0% or 100% based on high or low voltage setpoints.   
-  - the monitor will watch for your system to hit the configured 100% state of charge voltage, then +  - as your bank charges/discharges  **the monitor counts Amps in and out**, thereby calculating the percentage of capacity used and percentage remaining.  **Any loads that bypass the shunt cannot be counted.** 
-  - counts Amps/Watts in and out while below that voltage, thereby calculating the percentage of capacity used and percentage remaining.  This is an imperfect science with lead batteries because 100% SoC is only reliable after a //complete// charge, and because different discharge rates will change the effective capacity.   Think of the monitor as general guidance for lead batteries rather than gospel. Lithium banks will align more closely with what the monitor shows+
  
-Note:  Watching amps trail off at the end of lead Absorption (endAmps) will also tell you when the bank is [[electrical:12v:charging|fully charged]].  The battery manufacturer will specify something like [[electrical:12v:battery_capacity|C/200]] or C/100 as a sign Absorption is complete+Note:  [[electrical:solar:status|Watching amps trail off]] at the end of lead Absorption (endAmps) will also tell you when the bank is [[electrical:12v:charging|fully charged]]; you might manually reset to 100% at that time
  
 +===== drift and reset  =====
  
 +Small problems accrue over time, reducing the monitor's usefulness:
  
-===== Bogart Trimetric =====+  * the **measurement can be inaccurate** because current is very high or low relative to the shunt's working range.  To reduce these errors the shunt should be big enough to handle your largest expected simultaneous currents comfortably without being grossly oversized.   
 +  * the measurement and counting is **accurate but is not reliable for estimating changes in state of charge**.  This isn't a significant issue with lithium, but lead chemistries have substantial charging inefficiencies((10-20% in Absorption and 100% in Float since that stage is just offsetting self-discharge)) and consume more capacity than the count would suggest at higher currents (Peukert effect).   
 +  * or a combination of the above 
  
-[[https://amzn.to/2GQYZZN|{{ https://images-na.ssl-images-amazon.com/images/I/41Vczv0VvML.jpg?100}}]]  The most famous battery monitor is the [[https://amzn.to/2AoCO7H|Bogart Tri-Metric TM-2030 series]].+For those reasons **the monitor needs to be reset regularly** ("zeroed", "calibrated") when the bank is at a known state of charge.  This can be done at 0% or 100%: 
 + 
 +  - automatically by the monitor when a certain voltage setpoint is achieved.((14.0v = 100%, for example)) 
 +  - manually by the user.  For practical reasons this reset is usually performed when the user observes the bank to be 100% SoC.   
 + 
 +One rule of thumb is to reset the monitor 1x/week.  There is no harm in doing a reset more often if you happen to notice it's sitting at 100%.  [Hopefully you won't regularly be encountering 0% - secessus] 
 + 
 +===== gotchas ===== 
 + 
 +  * Monitors aren't magic;  they are estimations. 
 +  * Lead batteries have a noticeable Peukert effect, varying apparent capacity depending on discharge current. The battery's rating is measured at C/20, or 5A per 100Ah of rated capacity.  Heavier loads will reduce apparent capacity, and lighter loads will increase apparent capacity. 
 +  * battery capacity "walks down" (reduces) with age and injury. Apparent Ah may have to be reduced.  
 +  * very high or very low charging currents can cause the reset voltage setpoints to be unreliable 
 + 
 + 
 + 
 + 
 + 
 + 
 +===== commercial examples ===== 
 + 
 + 
 + 
 +==== Victron SmartShunt ==== 
 + 
 +[[https://amzn.to/4bxDjw8|{{ https://m.media-amazon.com/images/I/71g0M+mQjIL._AC_UL320_.jpg?100}}]] 
 + 
 +The 500A SmartShunt is available in [[https://amzn.to/3IfWai1|as the bare bluetooth-enabled shunt]] or [[https://amzn.to/4bxDjw8|the BMV package which includes a display]]. The BMV also adds programmable visual and audible alarm and programmable relay.((https://www.victronenergy.com/upload/documents/Datasheet-SmartShunt-EN.pdf)) 
 + 
 +Both setups can provide voltage, current, and temperature information to the app or directly to other Victron gear like solar charge controllers.((the Orion-TR is a notable and much-lamented exception))    
 + 
 + 
 + 
 +==== Bogart Trimetric ==== 
 + 
 +[[https://ebay.us/PPD2Bc|{{ https://images-na.ssl-images-amazon.com/images/I/41Vczv0VvML.jpg?100}}]]  Before the arrival of the Victron SmartShunt the most famous battery monitor was the [[https://ebay.us/PPD2Bc|Bogart Tri-Metric TM-2030 series]].
  
 This monitor will interface and operate their [[https://amzn.to/2SuOYmr|SX-2030 solar charge controller]].  The monitor will still provide amp-counting and other metrics when used on it's own. This monitor will interface and operate their [[https://amzn.to/2SuOYmr|SX-2030 solar charge controller]].  The monitor will still provide amp-counting and other metrics when used on it's own.
Line 32: Line 89:
  
  
-===== inexpensive shunts ===== +==== inexpensive shunts ==== 
-[[https://amzn.to/2BO0Eto|{{https://images-na.ssl-images-amazon.com/images/I/41ZuQEfExvL._SY90_.jpg }}]]For folks who are [dis]charging at 50A/75A, cheaper shunt is available for 1/5th the price of a Bogart + 
 +Not everybody needs prosumer-grade monitors.  There are simpler models available for less money. 
 + 
 +=== AiLi === 
 + 
 +[[https://amzn.to/49wa9eV|{{ https://m.media-amazon.com/images/I/51-5-oQoDAL._AC_UL320_.jpg?100}}]] 
 +The most popular inexpensive shunts are probably [[https://amzn.to/49wa9eV|the round AiLi]]. They are somewhat cheaper off ebay and can be found for ~$25 shipped off AliExpress if you can wait that long.((Feb 2024 prices))   
 + 
 +As with many other Chinese products, they are also available under different names but appear to be functionally identical.   
 + 
 +The **three buttons** access 4 screens, described below. Each screen shows a 10-bar battery gauge State of Charge icon at the top and a small charge/discharge icon on the left.  When charging the battery gauge icon is animated (present SoC --> 100%) and when discharging it statically shows present SoC. 
 + 
 +== screens == 
 + 
 +  * the LEFT button is Voltage / left-arrow - selecting this button shows the bank voltage at bottom to 2 digits of precision:  XX.XXv  If the center SET button is held in this mode you can set the voltage at which the SoC is assumed to be 0%;  10.5v or whatever is correct for the chemistry.  Then press SET again to sve.   
 +  * the CENTER button is A/Ah/SET 
 +    * pressing the button once shows present current levels in Amps 
 +    * pressing the button again shows remaining Ah, as seen in the pic to the right 
 +    * //holding// this button in the Ah display((remember it is also a SET button)) allows you to edit the Ah capacity (left - right button to adjust, press set to save.  The left or right buttons can be held down in edit mode for rapid change) 
 +  * the RIGHT button is SoC%.  On this screen you can [[electrical:12v:battery_monitor#drift_and_reset|reset SoC]] to either 0% (hold LEFT button) or 100% (hold RIGHT button).   
 + 
 +== backlight == 
 + 
 +By default the backlight is ON when  discharging and FLASHING((slow pulsing)) when charging.  The backlight can be toggled OFF/ON by holding the LEFT+RIGHT buttons at the same time. With the backlight disable charge vs discharge is still displayed by small icons on the left side of the display.  
 + 
 +== quirks == 
 + 
 +The decimal point is small and moves as numbers increase.  Examples: 
 + 
 + 
 +  * 1**.**234A (also 0.123A) 
 +  * 12**.**34A 
 +  * 123**.**4A 
 + 
 +=== Renogy === 
 + 
 +[[https://amzn.to/3waIj9M|{{ https://m.media-amazon.com/images/I/61qo1E+V7KL._AC_UL320_.jpg?100}}]] 
 +Renogy sells [[https://amzn.to/3waIj9M|a 500 monitor]] that appears to be a typical Chinese unit like any other.   
 + 
 + 
 + 
 +=== other examples === 
 + 
 +[[https://amzn.to/2BO0Eto|{{https://images-na.ssl-images-amazon.com/images/I/41ZuQEfExvL._SY90_.jpg }}]]For folks who are [dis]charging at lower currents like 50A/75A, even cheaper shunts are available.
  
 Heavier-duty shunts are available (up to [[https://amzn.to/2XBeDiN|at least 350A]]). Heavier-duty shunts are available (up to [[https://amzn.to/2XBeDiN|at least 350A]]).
 +
 +Read the specs and comments for the monitors to ensure they measure current in/out of the battery.  Some inexpensive displays only measure in one direction. Monitors that appear to be useful for vandwellers:((do your own reading!))
 +
 +
 +  * [[https://amzn.to/33XJQzF|DC 0-120V 0-100A Volt Amp Ah Power Capacity Percent Battery Monitor Watt Meter]]
 +  * [[https://amzn.to/2FcJfjl|DROK DC 0-300V 200A... AH Monitor Panel with Hall Sensor]]
 +  * [[https://amzn.to/2DGlCzy|Yeeco Digital DC Multimeter, DC 0-90V 0-100A... Coulomb Time Meter Battery Capacity Tester Monitor...Hall Sensor]]
  
electrical/12v/battery_monitor.1587008856.txt.gz · Last modified: 2020/10/11 19:48 (external edit)