Differences

This shows you the differences between two versions of the page.

--- electrical:12v:voltage_sag [2022/03/16 13:29]
frater_secessus [do nothing]
+++ electrical:12v:voltage_sag [2024/03/10 13:58] (current)
frater_secessus [networked shunt]
@@ Line 6: / Line 6: @@
-Extreme example:  During heavy charging the controller might see 14v instead of the battery's 13v.  This 14v -> 13v difference is called voltage sag.  A similar thing happens in reverse when consuming power.  The battery might be 12.5v but an inverter running a big load might "see" 11.5v at its own terminals and shut off.
+Extreme example:  During heavy charging the controller might see 14v instead of the battery's 13v.  This 14v -> 13v difference is called voltage sag.  A similar thing happens in reverse when consuming power.  The battery might be 12.5v but an inverter running a big load might "see" 11.5v at its own terminals and shut off prematurely.((from the user's point of view)).  It also makes it difficult to assess [[electrical:depth_of_discharge|state of charge]] of lead batteries by voltage.
+Sag presents special challenges when charging [[electrical:12v:drop-in_lifepo4|lithium]] battery banks.    Since the majority of lithium's usable power is found in an **extremely narrow voltage range**((about 0.5v wide)) sag can result in wildly unpredictable/inconsistent charging.
 ===== approaches =====
@@ Line 15: / Line 16: @@
 This is the majority position since most are unaware of the issue, or don't judge it to be important.  And it may //not// be a problem since since
-  - solar-only charging is often low-current charging, minimizing sag
+  - solar-only charging is often low-current charging, minimizing charge-induced sag
   - lead-chemistry batteries often have a range of Absorption and Float [[electrical:solar:charge_controller_setpoints|setpoints]] (see below)
@@ Line 21: / Line 22: @@
 ==== shorten the circuit ====
-A shorter wiring run will have less sag than a longer run.  For this reason charging sources are mounted **as close to the battery bank as possible**.
+All other things being equal, a **shorter wiring run will have less sag** than a longer run.  For this reason charging sources are mounted **as close to the battery bank as possible**.
@@ Line 35: / Line 38: @@
 ==== adjust charging setpoints ====
+If your sag is consistent you could adjust your setpoints upwards.  If you have 0.2v sag and want 14.0v you would configure the setpoint to 14.2v.
+Or if your battery manufacturer offers a range of charging voltages like 14.0v - 14.4v you could configure 14.4v and know it will be ≤14.4v in real conditions.
 ==== voltage sense wire ====
-    use a separate voltage sensing circuit (just a pair of wires to the battery) for controllers that have this feature.  Since it's not carrying real current it's not thrown off by sag
+A voltage sense wire is a separate wiring circuit running from the battery bank to the controller's voltage sense terminals (if so equipped).
-networked shunt
+Since the circuit isn't carrying any real current there will be very little sag and even quite thin wires can be used to get an accurate voltage reading.  The controller will then adjust output voltage to put the desired setpoint voltage into the bank.
-    use a controller that talks to a shunt at the battery
+Example:  The absorption setpoint (Vabs) is 14.0.  The sensed battery voltage is only 13.8v, so the controller actually puts out 14.2v.((or whatever it takes to get 14.0v at the battery))
+Some sense "wire" are wireless ([[https://amzn.to/3IbnnQg|Victron Smart Battery Sense]])
-==== calibration ====
+==== networked shunt ====
+Some controllers use networked [[electrical:12v:battery_monitor|battery monitors]] to report back what the battery voltage is in reality.
+Examples:
+  * [[https://amzn.to/3tiqlhu|Victron Lynx shunt]]
+  * [[https://amzn.to/3qbfcNJ|Victron VEbus smart dongle]]
+  * [[https://amzn.to/3ijF6u9|Victron BMV-712]].
+==== calibration ====
+The controller may also have a **voltage calibration** setpoint.  If your sag is consistently -0.2v you could input that calibration.  You put in 14.0v or whatever you want and the controller increases voltage by 0.2v.
-    have a voltage calibration setting - sag varies with current so the user might need to figure out average sag in their use case.
+Unfortunately, sag varies with current so the user might need to figure out average sag in their use case.

RV and vandwellers wiki

User Tools

Site Tools

Differences

Page Tools