User Tools

Site Tools


electrical:solar:output

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
electrical:solar:output [2021/04/28 13:04]
frater_secessus [solar magnifiers]
electrical:solar:output [2024/02/21 11:49] (current)
frater_secessus [panel tilt]
Line 1: Line 1:
 +[[lifestyle:words_of_wisdom|Words of wisdom]]:  "In theory, Imp * Vmp = panel Watts. There's an awful lot in the real world that can affect that." -- Cariboocoot((https://forum.solar-electric.com/discussion/comment/152013#Comment_152013))
 +
 +
 ====== Factors affecting solar panel output ====== ====== Factors affecting solar panel output ======
  
-For various reasons **it will be a rare event when your panels put out their full rated power**.  One reason for this is **the power needs somewhere to go**;  unless you are in [[electrical:12v:charging#bulk_stage|Bulk stage]] or are running big loads //the power isn't needed// so //the power isn't generated//.  +For various reasons **it will be a rare event when your panels put out their full rated power**.  One reason for this is **the power needs somewhere to go**;  unless you are in [[electrical:12v:charging#bulk_stage|Bulk stage]] or are running big loads //full power isn't needed// so //full power isn't generated//.  
  
-The other big reason is that **power ratings are derived from testing under specific lab conditions**.  The standard lab test is at:+The other big reason is that **power ratings are derived from testing under specific lab conditions**.((STC - Standard Testing Conditions))  The standard lab test is at:
   - //cell// temperature of 25C, which would be an //ambient// temperature of about 0C (freezing).  Panel voltage decreases significantly as cell temperature increases.      - //cell// temperature of 25C, which would be an //ambient// temperature of about 0C (freezing).  Panel voltage decreases significantly as cell temperature increases.   
   - 1000w of insolation per square meter of panel.  That is the amount of sun when the sun is directly overhead on a clear day.  Insolation maps will estimate [[#insolation_maps|how much sun]] various regions get.((This is what a panel's //efficiency// refers to:  the percentage of 1000w the panel can harvest per square meter of surface area.))   - 1000w of insolation per square meter of panel.  That is the amount of sun when the sun is directly overhead on a clear day.  Insolation maps will estimate [[#insolation_maps|how much sun]] various regions get.((This is what a panel's //efficiency// refers to:  the percentage of 1000w the panel can harvest per square meter of surface area.))
  
 A situation where you might get the panel's rated power (or even a bit more!) would be when the sun is directly overhead on a cold, clear day at high altitude.  Least power would be produced on a hot, overcast day when the sun is low on the horizon.  A situation where you might get the panel's rated power (or even a bit more!) would be when the sun is directly overhead on a cold, clear day at high altitude.  Least power would be produced on a hot, overcast day when the sun is low on the horizon. 
 +
 +Because the difference between lab and actual conditions is so large, some manufacturers also publish [[https://www.infiniteenergy.com.au/difference-between-max-power-stc-noct/|NOCT]]((Nominal Operating Cell Temperature)) specs, a //derated// (lowered) set of specs which might or might not be more indicative of what you will see in your use case.  NOCT is another tool in the toolbox, not gospel truth. 
 +
 +In practical terms, it's common to see a maximum of 75% of STC under good conditions, more under great conditions, and much less under poor solar conditions. And about half of that in winter. 
 +
 +===== where and when =====
 +
 +
 +The location and season both have profound effects on solar harvest. [[opinion:frater_secessus:panelsizesforinsolation#representative_areas|For example]], Phoenix AZ has **over 8.5x the amount of solar power** available in summer as Seattle WA in the winter.  For any given location, winter harvest will be about half of summer harvest. 
 +
 +You can estimate solar harvest using [[electrical:solar:pvwatts|models like PVwatts]].
 +
 +
 +
 +
 +===== lack of demand =====
 +
 +Solar panels do not //push// power;  they respond to the [[electrical:solar:charge_controller|solar charge controller]]'s demand as it tries to meet your present needs.  When those needs are minimal (battery already charged, small loads) the controller and panels will be loafing.  
 +
 +Related:  [[electrical:solar:status|is my solar working?]]
 ===== charge controller type ===== ===== charge controller type =====
  
Line 14: Line 37:
 [[electrical:solar:charge_controller#mppt|MPPT]] controllers can run the panel at max output when needed, but are much more expensive.  [[electrical:solar:charge_controller#mppt|MPPT]] controllers can run the panel at max output when needed, but are much more expensive. 
  
 +===== overpaneling =====
 +
 +Perhaps counterintuitively, setups with [[electrical:solar:overpaneling#vs_charge_controller|ample panel]] may see lower peak outputs than smaller setups.  This occurs because the overpaneled systems can get the bank charged before local solar noon when maximal harvest can be observed.  This is a feature, not a bug.  Overpaneled systems are built to meet needs under less-than-optimal conditions.  If you want to see Big Numbers, start a huge load at local solar noon under good solar conditions. 
 ===== wiring losses ===== ===== wiring losses =====
  
Line 43: Line 69:
  
 So a [[camping:snowbirding|snowbird]] who "chases 60" will be losing ~10% of panel output during the warmest part of the day.  Snowbirds chasing 70 will be losing ~13% of panel output. So a [[camping:snowbirding|snowbird]] who "chases 60" will be losing ~10% of panel output during the warmest part of the day.  Snowbirds chasing 70 will be losing ~13% of panel output.
 +
 +Note:  sub-freezing temperatures can push Voc/Vmp above their rated values.  If you will use solar in sub-freezing conditions leave plenty Voc headroom in your solar charge controller spec.
  
 Note: that [[hvac:insulation#heat_from_solar_panels|radiated heat from the underside of panels can raise temperatures inside the camper]]. Note: that [[hvac:insulation#heat_from_solar_panels|radiated heat from the underside of panels can raise temperatures inside the camper]].
Line 49: Line 77:
 ===== zenith angle ===== ===== zenith angle =====
  
-The sun will climb in the sky until it reaches its highest point for the day (local solar noon), then will start dropping again.  For a given latitude and time of day [[https://www.esrl.noaa.gov/gmd/grad/solcalc/azel.html|the sun's location in the sky is calculable]] and can give you the //cosine of solar zenith angle// ("cosine" hereafter).((the complement of elevation angle)).    You can use the cosine to understand how much power your system might put out.  +The sun will climb in the sky until it reaches its highest point for the day (local solar noon), then will start dropping again. This affects how much power you can harvest: 
 + 
 +{{ https://www.solarreviews.com/content/images/blog/post/212-PSH.jpg?500 }} 
 + 
 +For a given latitude and time of day [[https://www.esrl.noaa.gov/gmd/grad/solcalc/azel.html|the sun's location in the sky is calculable]] and can give you the //cosine of solar zenith angle// ("cosine" hereafter).((the complement of elevation angle)).    You can use the cosine to understand how much power your system might put out.  
  
 Examples:  if you have 200w of panels, your mppt controller typically yields 83% after derating, and the calculated cosine is .70 then you might expect ~116w in clear conditions at that time in that location.  (200 x .83 x .7 = 116.2).     Examples:  if you have 200w of panels, your mppt controller typically yields 83% after derating, and the calculated cosine is .70 then you might expect ~116w in clear conditions at that time in that location.  (200 x .83 x .7 = 116.2).    
Line 55: Line 87:
 Another way of thinking about this is that panel ratings are given for 1,000w/meter<sup>2</sup> At that time and place only 700w/meter<sup>2</sup> land on the panel.  (1000 x .70 = 700) Another way of thinking about this is that panel ratings are given for 1,000w/meter<sup>2</sup> At that time and place only 700w/meter<sup>2</sup> land on the panel.  (1000 x .70 = 700)
  
 +Tip:  you can work backwards from cosine calculations and observed power harvests to find your system's overall efficiency in different conditions.
  
 +==== paradox of big solar ====
 +
 +All other things being equal, peak harvest will happen at local solar noon((rarely clock-noon)) when the sun is highest in the sky. 
 +
 +This leads to a paradox:  some systems with [[electrical:solar:overpaneling#vs_battery_bank|relatively large arrays]] will have completed Bulk charging before solar noon and so do not have the chance to demonstrate full output.  In this scenario a smaller array could theoretically show higher //peak// output power but could not produce more overall Wh over the course of the day than the larger array.  
  
  
Line 63: Line 101:
 //Insolation//((**In**coming **Sol**ar Radi**ation**)) is the the amount of solar power reaching the panels.  This can be affected by: //Insolation//((**In**coming **Sol**ar Radi**ation**)) is the the amount of solar power reaching the panels.  This can be affected by:
  
-    * hours of seasonal daylight +    * short term 
-    * clouds +      * angle at which rays strikes the panel (angle of incidence) due to time of day.  At low angles effectively less panel area is exposed to sunlight. 
-    * rain, fog +      * amount of atmosphere the rays have to penetrate (less at solar noon, more at other times or anytime sun is relatively lower on the horizon) 
-    * angle at which rays strikes the panel (angle of incidence).  At low angles effectively less panel area is exposed to sunlight. +      * clouds 
-    * amount of atmosphere the rays have to penetrate (less at solar noon, more at other times or anytime sun is relatively lower on the horizon) +      * rain, fog 
-    * air quality:  \\ smoke((http://www.cheaprvliving.com/forums/showthread.php?tid=26592&pid=333826#pid333826)),((http://www.cheaprvliving.com/forums/showthread.php?pid=331627#pid331627))+      * air quality:  \\ smoke((http://www.cheaprvliving.com/forums/showthread.php?tid=26592&pid=333826#pid333826)),((http://www.cheaprvliving.com/forums/showthread.php?pid=331627#pid331627))
     * altitude (total irradiance ~+2.67%/1000')((https://www.sciencedirect.com/science/article/abs/pii/S1011134496000188))     * altitude (total irradiance ~+2.67%/1000')((https://www.sciencedirect.com/science/article/abs/pii/S1011134496000188))
 +    * humidity((https://www.researchgate.net/publication/338412686_Performance_study_of_Monocrystalline_and_Polycrystalline_solar_PV_modules_in_tropical_environments))
 +    * long term - roughly speaking, you can expect ~half the harvest in winter compared to summer
 +      * solar angle due to **time of year**. 
 +      *  hours of seasonal daylight
 +
 +   
 +Even the altitude and type of clouds can affect harvest:
 +
 +> in addition to total sky cover, cloud type is a significant factor in determining the reduction in solar radiation. In particular high, thin cirriform clouds are significantly less effective in reducing solar radiation than are lower, thicker clouds.((https://www.osti.gov/servlets/purl/6835171))
  
  
Line 95: Line 142:
  
  
 +==== using PVWatts to find FSE and daily harvest ====
 +
 +
 +this subsection has been [[electrical:solar:pvwatts|moved here]]
 ==== insolation maps ==== ==== insolation maps ====
-Insolation maps attempt to combine the effects of the variables above to estimate hours of **full sun((1000W/square meter)) equivalent** (FSE) per day.  +Insolation maps attempt to combine the effects of the variables above to estimate hours of **full sun((1000W/square meter)) equivalent** (FSE) per day for large areas.  This can be helpful when planning [[camping:snowbirding|moves around the country]].   
  
  
Line 108: Line 159:
 [[https://web.archive.org/web/20180811212703/http://www.solarinsolation.org/wp-content/uploads/2012/01/Solar_insolation.jpg|cities FSE by month]] [[https://web.archive.org/web/20180811212703/http://www.solarinsolation.org/wp-content/uploads/2012/01/Solar_insolation.jpg|cities FSE by month]]
  
 +[[https://solarpanelpower.ca/wp-content/uploads/2018/06/Full-Size-Solar-Power-Map-Canada.png|Canadian FSE]]
  
 ==== Derated output X FSE ==== ==== Derated output X FSE ====
Line 134: Line 186:
 ===== solar magnifiers ===== ===== solar magnifiers =====
  
-Some conditions can cause an effective magnification of solar power, the opposite of shade in a way.  This is usually caused by reflection of previously-uncaptured light onto the panels -- the panels are receiving both normal //direct// light and the additional //reflected// light at the same time. Since panels are rated at a lab standard 1000w/meter^2, this multiplication of available light can cause the panels to make more than their rated power, and can cause Voc to rise beyond rated specs.  +{{ https://sky-lights.org/wp-content/uploads/2020/04/2020-04-20-S4.jpg?150|https://sky-lights.org/2020/04/20/cloud-edge-effects-on-solar-arrays/}} 
 +Some conditions can cause an effective magnification of solar power, the opposite of shade in a way.  This is usually caused by reflection of previously-uncaptured light onto the panels -- the panels are receiving both normal //direct// light and the additional //reflected// light at the same time. Since panels are rated at a lab standard 1000w/meter<sup>2</sup> , this multiplication of available light can cause the panels to make more than their rated power, and can cause current and/or voltage to rise beyond rated specs.  
  
 Examples: Examples:
Line 141: Line 194:
   * intentional reflection from reflectors (as on a solar farm)   * intentional reflection from reflectors (as on a solar farm)
   * reflection off snow   * reflection off snow
-  * edge-of-cloud effect, where sunlight that would otherwise land elsewhere is reflected by clouds "near" the sun onto the panels. +  * edge-of-cloud effect, where sunlight that would otherwise land far away elsewhere is reflected by clouds "near" the sun onto the panels.   This is a relatively rare phenomenon, most often observable in overcast when there is a small break in thick clouds between the sun and panels.  
  
  
 ===== panel tilt ===== ===== panel tilt =====
  
-Insolation figures are given for flat surfaces((like flat-mounted panels)) but you can increase yield by keeping the panel more perpendicular to the sun.  The downsides are setup and takedown time/effort, and (with van-mounted panels) the requirement to park the van at a particular angle in the campsite.   Tilt might be more practical for people who stay in one place for longer periods rather than moving every couple of days+Insolation figures are given for flat surfaces((like flat-mounted panels)).  This means //when the sun is low in the sky//((and skies are clear not overcast -- see below)) you may be able to increase solar yield by tilting the panels toward the sun.  In effect the panel is more perpendicular to the sun so it can capture maximal solar energy
  
-**Optimum aiming** involves both tracking the suns elevation above the horizon (zenith) and tracking the sun's east-to-west travel (azimuth).  Doing both can increase yield ~30% but requires frequent repositioning.+Pro: 
 + 
 +  * optimal tilt will increase harvest when the sun is low and skies are clear.((peak harvest numbers are more impressive but of less import.)) 
 +  * can be used to further increase harvest if roof space is maxxed (cannot add more panel) 
 + 
 +Con: 
 + 
 +  * setup and takedown time/effort.  Tilt might be more practical for people who stay in one place for longer periods rather than moving every couple of days. One's ability to drive off quickly might be impeded.  
 +  * with vehicle-mounted panels,  the requirement to park at a particular angle in the campsite 
 +  * tilt advantage is greatest when available power is least (ie, the sun's position in the sky is lowest), as in winter, high latitudes, morning/afternoon, etc.  So if you have a 200w array that averages **75w** when the sun is low in the winter adding tilt could make the array behave like a 260w array making **98w**.   
 +  * tilt has minimal effect when sunlight is indirect (rain, overcast, fog, haze, etc) .    
 + 
 + 
 +**Optimum aiming** involves both tracking the suns elevation above the horizon (zenith) and tracking the sun's east-to-west travel (azimuth).  Doing both can increase yield ~30% but requires frequent repositioning throughout the day.
  
 **Leaving panel tilt in a reasonable default** is more common and has milder yield improvments.  In this approach the panel is aimed at true((not magnetic)) south((in the northern hemisphere)) at a particular angle from perpendicular((ie, flat panel)) depending on time of year and latitude. **Leaving panel tilt in a reasonable default** is more common and has milder yield improvments.  In this approach the panel is aimed at true((not magnetic)) south((in the northern hemisphere)) at a particular angle from perpendicular((ie, flat panel)) depending on time of year and latitude.
Line 161: Line 227:
  
  
 +Further reading:
  
 +  * [[https://www.gonewiththewynns.com/tilt-rv-solar-panels|results of tilt experiments]] by Gone With the Wynnes
 ===== cleanliness ===== ===== cleanliness =====
  
-According to Sandia lab testing, dusty panels cause a derating of about 5%.((FIXME citation))+[[https://www.sciencedirect.com/science/article/pii/S1876610214011874|According to lab testing]], dusty panels cause a derating of 5%-6%. 
 + 
 ===== further information ===== ===== further information =====
  
electrical/solar/output.1619629443.txt.gz · Last modified: 2021/04/28 13:04 by frater_secessus