Differences

This shows you the differences between two versions of the page.

--- electrical:solar:shading [2020/01/07 23:12]
frater_secessus [partial shading]
+++ electrical:solar:shading [2022/08/06 15:18]
frater_secessus [Partial shading]
@@ Line 1: / Line 1: @@
-====== Shading ======
+Words of Wisdom:  "The response of a series parallel array to shade will be complicated." -- sensij((https://www.solarpaneltalk.com/forum/solar-panels-for-home/solar-panel-installation/365350-understanding-shade-and-low-light-conditions?p=365396#post365396))
-Shading can
+====== Partial shading ======
+Partial shading can have surprisingly dramatic effects on [[electrical:solar:output|panel output]]. Perhaps counterintuivitely, //partial// shading can have more devastating effects on output than //full shading// like heavy overcast or evenly shaded forest canopies.
-===== even shading =====
+===== reminder:  how panels work =====
-Even shading might
+**Before we begin:** solar panels are "current sources";  their voltage pops up into the normal range in any kind of meaningful light(>= 20% [[electrical:solar:output|insolation]]) but current will suffer.
+Partial shading in this context means:
+  * light is falling on the panel
+  * but not evenly on the panel -- it is different on some cells
-===== partial shading =====
+To prevent power from rushing into the shaded string and overheating them, panels have bypass diodes between the strings.  Basically the shaded strings get cut off, electrically speaking, to protect them. In a perfect world each cell would be protect by a lossless, costless diode but that's not possible yet.  :-)
-Partial shading is problematic for solar panels because:
- - partial shade causes voltage differences between cells
+===== panel configuration for partial shade =====
- - voltage differences cause power to rush
-When a panel is partially shaded the individual cells are running at differing voltages.  If the cells were bare then the unshaded (normal voltage) cells would backfeed power into the shaded (lower voltage) cells, overheating them.  To prevent this, panel manufacturer's insert diodes.
+The way to avoid the problems associated with partial shade is to avoid partial shade.  :-)  Failing that, there are steps one can take to minimize the losses:
+  * **avoiding shade** is best
+  * a **dedicated controller for each panel** is the next best thing
+  * [[electrical:solar:panels|amorphous/thin-film panels]] are less affected by shade
+  * With **PWM controllers, parallel panel configurations typically yield more power** in partial shade than serial.
+  * With **MPPT controllers** and **low-ish voltage** serial panel configurations (where the total Vmp is <=2x battery bank voltage) **parallel will probably still yield more**.
-The takeaway:
-  *  With PWM controllers **parallel panel configurations typically yield more power** in partial shade than serial.
+===== exception:  high voltage strings + mppt =====
-  * With MPPT controllers and **low-ish voltage** serial panel configurations (where the total Vmp is <=2x battery bank voltage) it's close but **parallel will probably still yield more**.
-  * With MPPT controllers and **higher voltage** serial configs (say Vmp is >=3x bank voltage) we see **an increasing serial advantage over parallel in partial shade**.
+There is another approach, which is to **bring the shaded cells/strings back online by bringing the rest of the panel down to their level**.  It sounds counterproductive, but with MPPT controllers and in some higher-voltage series configurations (say Vmp is >=3x bank voltage) it works.
+This occurs because the MPPT has a broader range of voltages to sweep and can find [[https://www.sciencedirect.com/science/article/abs/pii/S0960148113006952|other power peaks]] (panel voltages) that are **low enough to bring the shaded cells back online** but still **high enough to charge the battery bank**.  It's  not reality, but we can think of it as MPPT evenly "shading" the entire panel voltage-wise in order to get max juice from it in partial shade conditions.((https://diysolarforum.com/threads/mppt-sizing.17947/post-208104))
+===== examples =====
+  * [[https://www.youtube.com/watch?v=QzzB1i1w_kM|altE video on partial shading]]
+  * [[https://www.youtube.com/watch?v=ofo1HQyGG8s|wiring shaded panels]]
+  * [[https://www.rv.net/forum/index.cfm/fuseaction/thread/tid/28152689.cfm|Solar Panel Shadows and Bypass Diodes]]

RV and vandwellers wiki

User Tools

Site Tools

Differences

Page Tools