This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
electrical:solar:panels [2023/08/23 19:15] frater_secessus [Efficiency] |
electrical:solar:panels [2024/05/28 15:50] frater_secessus [Specifications] |
||
---|---|---|---|
Line 142: | Line 142: | ||
===== efficiency ===== | ===== efficiency ===== | ||
+ | |||
+ | The formula for panel efficiency is simply rated watts / square meter. | ||
+ | |||
Higher efficiency doesn' | Higher efficiency doesn' | ||
Line 147: | Line 150: | ||
In general, mono has higher efficiency than poly, and poly has higher efficiency than thin film. | In general, mono has higher efficiency than poly, and poly has higher efficiency than thin film. | ||
- | The cost of higher efficiency panels typically outstrips the increase power, so unless you are tight for space they typically aren't a good value for money. | + | The cost of higher efficiency panels typically outstrips the increase power, so unless you are tight for space they typically aren't a good value for money. |
- | > At zenith, sunlight provides an irradiance of just over 1 kilowatt per square meter at sea level. Of this energy, 527 watts is infrared radiation, **445 watts is visible light**, and 32 watts is ultraviolet radiation. -- [[https:// | ||
- | |||
- | Mono panels can capture about 15-20% of this visible light energy. | ||
===== longevity ===== | ===== longevity ===== | ||
Line 171: | Line 171: | ||
* **Maximum Power Voltage (Vmp)**: | * **Maximum Power Voltage (Vmp)**: | ||
* **Maximum Power Current (Imp)**: | * **Maximum Power Current (Imp)**: | ||
+ | * **Temperature coefficient**; | ||
Note that in this example the Power (W) rating is 190, which is the Vmp x Imp (28.60 x 6.64 = 189.904W). | Note that in this example the Power (W) rating is 190, which is the Vmp x Imp (28.60 x 6.64 = 189.904W). | ||
Line 176: | Line 177: | ||
In real world conditions [[electrical: | In real world conditions [[electrical: | ||
- | Panels | + | ==== temperature coefficient ==== |
+ | |||
+ | Panel voltage // | ||
+ | |||
+ | - since panels are rated by Vmp x Imp, anything that reduces voltage will reduce power.((PWM are generally not affected since they are not using that higher voltage anyhow)) | ||
+ | - the Vmp your MPPT controller finds in human-comfortable temps will likely be lower than rated Vmp | ||
+ | |||
+ | Example: | ||
+ | |||
+ | The actual amount of drop is dictated by the **temperature coefficient**, | ||
+ | |||
+ | This coeffcient ranges from 0.3% to -0.5%. | ||
+ | |||
+ | Let's consider three different panels in 80F ambients: | ||
+ | |||
+ | * 100w mono, rated 19Vmp, -0.445%/ | ||
+ | * 100w poly, rated 18Vmp, -0.440%/ºC == **14.48w** lost @ 15.39Vmp | ||
+ | * 100w CIGS((not really, trying for apples-to-apples here)), rated 18.66Vmp, -0.36%/ºC == **11.85w** lost @ 16.45Vmp | ||
+ | |||
+ | |||
+ | |||
==== STC and NOCT ==== | ==== STC and NOCT ==== | ||
Line 191: | Line 213: | ||
While NOCT may be useful for gauging normal harvests, STC is used for system component((like controllers)) sizing because the panels really can make STC power((or even more)) in some real world conditions. | While NOCT may be useful for gauging normal harvests, STC is used for system component((like controllers)) sizing because the panels really can make STC power((or even more)) in some real world conditions. | ||
+ | |||
+ | >> NOCT is useful for comparing two panels **[that have] the same STC rating**. A panel with a higher rated power at NOCT for example, will generally result in a higher performing panel.((https:// | ||
**PTC** ([[https:// | **PTC** ([[https:// |