This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
electrical:solar:pwm_tweaking [2019/07/17 08:20] frater_secessus [set Vabs and Vfloat relatively high] |
electrical:solar:pwm_tweaking [2025/03/18 12:35] (current) frater_secessus [PWM's achilles heel] sag |
||
---|---|---|---|
Line 7: | Line 7: | ||
- | ===== the controller's achilles heel ===== | + | ===== PWM's achilles heel ===== |
- | During charging with a PWM controller **the solar panel will be running at the voltage of the battery bank**. | + | During charging with a PWM controller **the solar panel will be running at the voltage of the battery bank**.((or close enough for the purposes of this discussion. |
This affects charging in all three [[electrical: | This affects charging in all three [[electrical: | ||
- | {{ http:// | + | {{ http:// |
- | 17.8v x 5.6A = 99.68w | + | 17.8v x 5.6A = 100w <-- rating under laboratory conditions((the math doesn' |
- | 17.8v x 5.6A = 94.70w <-- MPPT running at 95% efficiency \\ | + | 17.8v x 5.6A = 94.70w <-- MPPT running at 95% efficiency |
+ | |||
+ | PWM harvest | ||
14.8v x 5.6A = 82.88w <-- power at a high Absorption voltage, as with flooded lead acid \\ | 14.8v x 5.6A = 82.88w <-- power at a high Absorption voltage, as with flooded lead acid \\ | ||
14.4v x 5.6A = 80.64w <-- power at a lower Absorption voltage \\ | 14.4v x 5.6A = 80.64w <-- power at a lower Absorption voltage \\ | ||
Line 24: | Line 26: | ||
12.7v x 5.6A = 70.61W <-- power at 100% state of charge (SoC) \\ | 12.7v x 5.6A = 70.61W <-- power at 100% state of charge (SoC) \\ | ||
12.4v x 5.6A = 69.44W <-- power at 75% state of charge; bulk charging \\ | 12.4v x 5.6A = 69.44W <-- power at 75% state of charge; bulk charging \\ | ||
- | 12.1v x 5.6A = 67.76W <-- power at 50% state of charge; | + | 12.1v x 5.6A = 67.76W <-- power at 50% state of charge; |
+ | 10.0v x 5.6A = 56.00W <-- battery bank accidentally run flat | ||
This last number shows how far off PWM output can fall when battery voltage (Vbatt) is at its lowest.((The last number is also the source of the "30% boost!!!" | This last number shows how far off PWM output can fall when battery voltage (Vbatt) is at its lowest.((The last number is also the source of the "30% boost!!!" | ||
Line 48: | Line 51: | ||
Using the above panel as an example, Vabs of 14.7v will yield 3.5% more power than a Vabs of 14.1v. | Using the above panel as an example, Vabs of 14.7v will yield 3.5% more power than a Vabs of 14.1v. | ||
- | Note: consult the battery manufacturer' | + | Note: consult the battery manufacturer' |
+ | DO invest in the $10 temperature probe option. | ||
==== battery: maintain a higher state of charge ==== | ==== battery: maintain a higher state of charge ==== | ||