RV and vandwellers wiki

User Tools

Site Tools

Trace:
electrical:12v:alternator_details

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
electrical:12v:alternator_details [2023/09/24 12:27]
frater_secessus [current] 		electrical:12v:alternator_details [2024/03/29 19:48] (current)
frater_secessus [external regulation]
Line 52: Line 52:
 **Externally-regulated alternators** are alternators where the regulation function is physically separated from the alternator.  There may be a stand-alone external regulator or the engine ECU may assume those duties.   **Externally-regulated alternators** are alternators where the regulation function is physically separated from the alternator.  There may be a stand-alone external regulator or the engine ECU may assume those duties.  
  
-In a camper/RV context //an externally-regulated alternator// typically means an **aftermarket regulator**, like Balmar - voltage often provides [[electrical:12v:charging|multistage (smart) charging]], temperature-based derating, etc.  Read on.  +see [[electrical:12v:alternator_details#external_regulation|External Regulation]] below
- +
-A separate alternator (see below) is not required to use external regulation but that is a common scenario.  If one externally regulates the vehicle's sole alternator the chassis could be exposed to higher or lower voltages than it was designed for.  +
- +
-Common external regulators include: +
- +
-  * Balmar ARS-5 (no external voltage sensing) +
-  * Balmar MC-614 (external voltage sensing) +
-  * Xantrex Xar (no external voltage sensing) +
-  * Wakespeed WS500 (CANBUS)+
  
 === tricking the regulator === === tricking the regulator ===
Line 131: Line 122:
  
  
-=== heat ===+==== heat ====
  
  
Line 177: Line 168:
 === thermal switches === === thermal switches ===
  
-In [[https://www.youtube.com/watch?v=bjeHJd6OO2Y&lc=Ugyusa6wH9p3jNMKbmh4AaABAg.9m5OeSgBRtB9m5UO1ANIfF|a comment]] on [[https://www.youtube.com/watch?v=bjeHJd6OO2Y|an excellent video about charging lithium from the alternator]] WorkingOnExploring talks about adding overtemp protection with:+In [[https://www.youtube.com/watch?v=bjeHJd6OO2Y&lc=Ugyusa6wH9p3jNMKbmh4AaABAg.9m5OeSgBRtB9m5UO1ANIfF|a comment]] on [[https://www.youtube.com/watch?v=bjeHJd6OO2Y|an excellent video about charging lithium from the alternator]] WorkingOnExploring talks about adding overtemp protection with a thermal switch (a small bimetallic switch):((see [[https://www.youtube.com/watch?v=kF4Yxo9C9DM|this teardown and demo video]]  on youtube)) 
  
 >>  [[https://amzn.to/3luTwwx|a KSD9700 120C]], normally closed thermal switch epoxied to your alternator case. That way, if some abnormal event occurred and the alternator overheated, it could deactivate the [combiner] till the alternator cooled. It would likely cost less than $20 to install this thermal safety. >>  [[https://amzn.to/3luTwwx|a KSD9700 120C]], normally closed thermal switch epoxied to your alternator case. That way, if some abnormal event occurred and the alternator overheated, it could deactivate the [combiner] till the alternator cooled. It would likely cost less than $20 to install this thermal safety.
Line 183: Line 175:
 The idea here is to run the relay's control circuit((manual or D+ wire, //not// the charging wire)) through the **N**ormally-**C**losed((ie,circuit completed)) thermal switch.  When the switch hits the defined temperature the circuit opens((breaks)) and power to the combiner is cut off;  house bank charging from the alternator is stopped. The switch will typically reset when temperature drops by ~25%; read the datasheet for your switch for specific details.  The idea here is to run the relay's control circuit((manual or D+ wire, //not// the charging wire)) through the **N**ormally-**C**losed((ie,circuit completed)) thermal switch.  When the switch hits the defined temperature the circuit opens((breaks)) and power to the combiner is cut off;  house bank charging from the alternator is stopped. The switch will typically reset when temperature drops by ~25%; read the datasheet for your switch for specific details. 
  
-The thermal switch is a tiny bimetallic device.  See [[https://www.youtube.com/watch?v=kF4Yxo9C9DM|this teardown and demo video]] (youtube).+If one had a DC with a current-limiting function ([[electrical:12v:b2b#renogy1|renogy's 20-40-60A models]], for example) or DC-DC in parallel one could use two different-spec switches to achieve staged charging.  Using placeholder temps: 
 + 
 +  - run an aggressive charging setup full blast  
 +  - at 90C engage current limiting 
 +  - at 120C disable charging completely 
 + 
 + 
  
 Note:  120C = 248F.  Other temps like 90C (194F) and 100C (212C) are available and may be gentler on the alternator. Because the alternator is mounted to the block the alternator case may be at the ~same temp as the block.  Check case temps when engine has been running to get a feel for how hot the case should be, preferably at the location the diodes are heat-sinked to the alternator case.((https://forums.sailboatowners.com/threads/alternator-temperature.1249925187/post-1644191))    Note:  120C = 248F.  Other temps like 90C (194F) and 100C (212C) are available and may be gentler on the alternator. Because the alternator is mounted to the block the alternator case may be at the ~same temp as the block.  Check case temps when engine has been running to get a feel for how hot the case should be, preferably at the location the diodes are heat-sinked to the alternator case.((https://forums.sailboatowners.com/threads/alternator-temperature.1249925187/post-1644191))   
Line 227: Line 226:
 ==== external regulation ==== ==== external regulation ====
  
-External regulation can provide overtemperature protection (see section on Heat above), and can also cause the alternator to behave like a smart charger with [[electrical:12v:charging|multistage charging]]. +External regulation can provide overtemperature protection (see section on Heat above), current limiting, and can also cause the alternator to behave like a smart charger with [[electrical:12v:charging|multistage charging]].  
 + 
 + 
 +In a camper/RV context //an externally-regulated alternator// typically means an **aftermarket external regulator** controlling a **dedicated secondary alternator**.((on boats there is typically one externally-regulated alternator that runs the electrics and charges the house bank.  Modern land vehicles are likely less tolerant of the alternator doing things the ECU did not command.))  Depending on the implementation external regulation might provide: 
 + 
 +  * configurable current levels and/or voltage setpoints 
 +  * [[electrical:12v:charging|multistage (smart) charging]] 
 +  * temperature monitoring so maximal current can be extracted without overheating 
 +  * RPM-based output limits 
 +  * slowly ramping up current to avoid belt slippage/damage 
 +  * shutoff when commanded by BMS 
 +  * CANBUS and other communication 
 +  * etc 
 + 
 +External regulators include: 
 + 
 +  * Balmar ARS-5 (no external voltage sensing) 
 +  * Balmar MC-614 (external voltage sensing) 
 +  * Xantrex Xar (no external voltage sensing) 
 +  * Wakespeed WS500 (CANBUS) 
 +  * [[https://theyachtrigger.com/arco-zeus-alternator-regulator/|Arco Zeus]] - new to market 
 +  * [[https://www.mastervolt.com/products/alpha-pro-mb-charge-regulator1/alpha-pro-iii/|Mastervolt]], more often seen in marine installs 
 +  * [[https://sterling-power.com/collections/alternator-regulators|Sterling]]
  
  
Line 303: Line 324:
 [[https://youtu.be/uwrG3gUdDT8?t=725|This behavior surprised Mortons on the Move]], thwarting their alternator-charging plans.  [[https://youtu.be/uwrG3gUdDT8?t=725|This behavior surprised Mortons on the Move]], thwarting their alternator-charging plans. 
  
 +Known configurations:
  
   * 397A = 220A + 157A   * 397A = 220A + 157A
Line 317: Line 339:
  
  
 +== GM ==
 +
 +Information is limited, but GM factory dual alt setups appear to run the way one would expect in the first place, with load shared between them:
 +
 +> The two alternators are controlled over a common circuit from the ECM so they cannot be controlled independently. The ECM cannot shut one down and let the other one run. It is both or neither.((https://www.duramaxforum.com/threads/dual-alternator.934098/post-11906770))
  
 +[[https://www.duramaxforum.com/threads/dual-alternator.934098/post-11906642|This upfitters guide excerpt]] contains additional information.
 ==== DUVAC ==== ==== DUVAC ====
  
electrical/12v/alternator_details.1695572837.txt.gz · Last modified: 2023/09/24 12:27 by frater_secessus

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International

affilliate disclosure

CC Attribution-Noncommercial-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki