User Tools

Site Tools


electrical:12v:lvd

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
electrical:12v:lvd [2018/06/23 16:51]
frater_secessus [common LVD setpoints]
electrical:12v:lvd [2023/09/06 10:54] (current)
frater_secessus [examples]
Line 3: Line 3:
 A low voltage disconnect is used to stop loads from dragging a battery bank below a given voltage (Vlvd). A low voltage disconnect is used to stop loads from dragging a battery bank below a given voltage (Vlvd).
  
-The simplest way to implement an LVD is to wire all loads go through the LOAD output of the charge controller, and set the controller's Vlvd.  If system load is heavier than the LOAD output can provide, one may use: 
-  * a stand-alone LVD with higher current rating (more expensive) 
-  * or run loads off a [[electrical:12v:relay|relay]] triggered by the LVD (less expensive) 
  
- except the [[electrical:inverter|inverter]], due to the heavy current draw.  The inverter will have its own internal LVD.+===== examples ===== 
 + 
 +[[https://amzn.to/3Ri94RY|{{ https://m.media-amazon.com/images/I/51ODnDvz-rL._AC_UL400_.jpg?125}}]] 
 + 
 +  * [[https://amzn.to/3Ri94RY|Victron Battery Protect]] 
 +  * [[https://amzn.to/47Xzz5n|Blue Sea 7635 m-LVD]] 
 +  * [[https://www.amazon.com/s?k=low+voltage+disconnect&link_code=qs&tag=themousepad|various amazon listings]] 
 + 
 +One can also **DIY a low voltage disconnect**.   
 + 
 +In theory the simplest way to implement an LVD would be to wire all loads go through the [[electrical:solar:charge_controller#using_load_output|LOAD output]] of the charge controllerand set the controller's [[electrical:solar:charge_controller_setpoints|Vlvd]].  In practice this is rarely done for reasons given in the link above.  It is more common to run a [[electrical:12v:relay|relay]] on the LOAD output, which is triggered ON/OFF by the LVD setting: 
 + 
 +controller LOAD output -> relay -> loads((the LOAD triggers the relay, but actual power comes from the battery bank))   
 + 
 +If the controller has no LVD (or not no LOAD output at all) you can use a   [[https://amzn.to/3m2OTp3|stand-alone LVD]] powered by the battery 
 + 
 + 
 + 
  
 ===== common LVD setpoints ===== ===== common LVD setpoints =====
Line 22: Line 37:
  
  
-[[electrical:12v:lifepo4_batteries_thread|LiFePO4]] nominal 12v banks can be safely drained to 80-90% Depth of Discharge.  That point is something like 12.0v.((http://rvwiki.mousetrap.net/doku.php?id=electrical:12v:lifepo4_batteries_thread#notable_voltage_reference_points))+[[electrical:12v:deep_cycle_battery#lithium_chemistries[electrical:12v:lifepo4_batteries_thread|LiFePO4]] nominal 12v banks can be safely drained to 80-90% Depth of Discharge.  That point is something like 12.0v.((http://rvwiki.mousetrap.net/doku.php?id=electrical:12v:lifepo4_batteries_thread#notable_voltage_reference_points))
  
 ===== challenges ===== ===== challenges =====
electrical/12v/lvd.1529787093.txt.gz · Last modified: 2020/10/11 19:48 (external edit)